Geotextile Specifications for Filtration Separation and Reinforcement
Geotextile specifications should identify what will be tested, how a value is expressed and what must be achieved for acceptance. For high-strength woven reinforcement, a large number without direction, method or value basis leaves important questions unanswered.
This guide explains the fields a buyer should compare. Use the project specification and offered data sheet together, then identify gaps before approving a purchase.
Choose the specification route before reading the numbers
Geotextile specifications depend on the function. A separation fabric, a filter, a protection cushion and a tensile reinforcement should not be compared through one universal property table. First identify the job, then compare the required product with its own declared methods and acceptance limits.
| Function | Properties to identify in the project specification | Important distinction |
|---|---|---|
| Separation and construction survivability | Required strength, damage resistance and installation conditions | A reinforcement grade is not automatically required |
| Filtration | Soil compatibility, opening characteristics and hydraulic properties | Mass or ultimate strength alone does not describe filtration |
| Protection | Protection assessment with the actual contacting materials and loads | A puncture value alone is not a complete system assessment |
| High strength reinforcement | Directional tensile values, strain, continuity and applicable long term evidence | Short duration strength differs from long term design strength |
This guide focuses in detail on high strength woven reinforcement after that initial selection. For product supply, use the woven geotextile product page. For a needle-punched material, start with the geotextile range and provide the actual specification.
Understand kN per metre and direction
A value expressed in kN/m describes force per unit width. A value expressed as force alone may come from a different test arrangement. Similar numerical magnitudes do not establish equivalent performance.
Machine direction normally follows the roll length; cross direction is across the width. Confirm those definitions on the proposed product. A directional reinforcement must be installed in the orientation required by the drawing.
A 600/50 description therefore needs two clearly identified directions. It does not mean 600 kN/m in all orientations, and it does not define long-term design strength.
Compare methods before comparing numbers
Wide-width methods and grab methods use different specimen arrangements. Test names, specimen conditions, units and result descriptions should be visible in the submission.
ISO 10319 and ASTM D4595 are examples of geotextile tensile methods that can appear in specifications. Their use should follow the actual project requirement and the method’s applicability. At high strengths, the laboratory must have suitable gripping and load capacity.
Do not relabel one method’s result as another or convert force to force-per-width without a valid basis. If a substitution is proposed, have the approving party resolve it before accepting the material.
Identify the declared value and strain requirement
A typical value describes a different basis from a specified minimum or another statistical acceptance value. Ask what the offer promises and what the receiving inspection will check.
Some reinforcement requirements also specify strength at a defined strain or a limit on deformation. An ultimate tensile result does not automatically answer those requirements.
Keep both the value and its definition on the comparison sheet. An apparently higher breaking strength can still leave a required strain or acceptance condition unresolved.
Treat grade examples as descriptions
| Example enquiry description | What still needs confirmation |
|---|---|
| 200/50 kN/m | Direction convention, method and acceptance basis |
| 400/50 kN/m | Strain requirements, material and relevant documents |
| 600/50 kN/m | Offered product identity, test capability and design evidence |
These are illustrative grade descriptions, not a verified stock list. Use the woven product page for the product enquiry and the 600/50 supply case for one documented purchasing context.
Specify seams and hydraulic properties when required
If the design relies on a tensile connection, identify the seam configuration and required test evidence. Fabric tensile strength does not establish seam performance, and a simple overlap does not automatically transfer the design load.
If the fabric must also filter or separate soil, identify the applicable opening, flow and survivability requirements. High tensile capacity does not demonstrate suitable filtration for every soil.
Avoid adding a property only because another brochure lists it. The schedule should explain the actual requirements and the methods used to accept them.
Review long-term evidence for permanent reinforcement
Sustained loading, exposure and construction damage may affect the strength available under the design method. Request the product-specific information required by the project rather than deriving values from a catalogue percentage.
The material, grade and conditions covered by the evidence should match the proposed supply. Where a report is unavailable, record that gap and resolve it with the approving party before ordering.
Our basal reinforcement page explains how these material questions sit within an embankment design. The fabric specification alone does not replace that system assessment.
Turn the comparison into a usable material order
Record the accepted data-sheet revision, required values, dimensions, quantity and inspection schedule. Identify sample references and production records so the later shipment can be traced to what was approved.
Send Planetliner your specification or data sheet. We can review the requested supply and distinguish confirmed properties from those needing clarification, testing or project approval.